Welcome to www.pressroomelectronics.com

Sales: (800) 937-4334
       Service: (630) 443-9343



Pressroom Electronics US Manufacturer of Press Controls


Resolver Based Clutch Brake Controls

All Resolver Based Controls include the resolver and 30 foot of resolver connecting cables.

Please choose from the products listed below:


Exceeds OSHA 1910.217 & ANSI B11.1-2009, "Control Reliable Design," with dual logic power supplies, heavy duty resolver, System diagnostics and programming in plain English/Spanish which can control up to four sets of operator stations, Major faults such as E-Stop, motion, brake monitor, and sensor faults are handled by two force-guided relays (Form B safety relays), Off--inch--single--continuous, Continuous ARM; top stop, anti-tie down and anti-repeat, SPM Range (1 to 500), Password and supervisory controlled keyed selector switch for security of data entry, Interrupted stroke provision with indicator, Inch mode monitoring, Crank angle and speed readout (SPM), Time-based brake monitor, Built-in motion detector and drift fault, 90° and 270° stop time tester/meter built-in, Built-in hour meter for maintenance, Built-in variable speed compensation, Servo-feed interface built-in, Six optically isolated die protection inputs, Six PLS (programmable limit switch) output relays, 100 job memory, Stroke, batch, quality, and part counters, Batch counter output relay, Die protection output relay, Speed output relay, Auxiliary output relay, Optional Ethernet or DeviceNet and PC Link to allow offline job creation and storage.  Optional 10.1" color touchscreen replaces the standard display shown.  Touchscreen is show to the left.

 Small Form Factor

Small Form Package (SFP) Presscommander
Designed for installation in tight areas, on smaller presses, or by pendent mounting for convenient operator access to the press controls and machine status.

 PSC 05

Model PCS-05 
The  Board Only Commander Module  (Part #PCS-05).The redundant clutch/brake punch press control module with a remote panel mount message display (available in English or Spanish).
Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009.

 PCS-08 Model PCS-08
The redundant clutch/brake punch press control module with a remote panel mount message display (available in English or Spanish).
Also included are all of the switches, legend plates, push buttons, and indicator lights for easy mounting on to your existing control. Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009.
 PCS 10

Model PCS-10 
The compact Model PCS-10 is big in safety and automation control. The redundant clutch/brake punch press control module has a remote panel mount message display (available in English or Spanish).

 PCS 20

Model PCS-20
Encompasses all of the features and components of Model PCS-10 plus all of the following switches, legend plates, push buttons, and indicator lights for easy mounting into your existing control. Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2009.


Model PCS-2000
Completely prewired and
 ready for installation. System supplied complete with a well marked terminal strip for easy, safe, and accurate electrical interface to the various punch press components. Due to the hybrid design characteristics,  a main power disconnect switch and magnetic motor starter can be supplied in the same control panel.


Model PCS-4000 
Incorporates all the requirements of OSHA for control reliability and component monitoring. Also includes component and system diagnostics with indicator lights for total press monitoring. Complies with section 1910.217 of the Federal Register and ANSI Standard B11.1-2001.  When foot actuation is used, a method of guarding the point of operation must be provided.

 The Ultimate

The Ultimate 
The most feature intensive air clutch punch press control available. The control conforms to all current OSHA and ANSI standards for control reliability and component monitoring. System incorporates the PressCam 8 for complete punch press synchronization and flexibility for all peripheral punch press signaling needs such as feeds, die protection, lubrication, blow-offs, etc. All of the electrical timing adjustments for the complete press operation are done at the floor level by the operator. The PressCam 8 system also has a large job memory of 100. This gives the control the ability to remember 100 complete different jobs or die set-ups at the press. The memory concept at the press is an excellent feature due to the tremendous time saved during set-ups of various operations. Additional time is saved by being able to adjust or "fine tune" the stamping process while the press is running, which is an aid in maximizing press utilization.


  Resolver Based Replacement Parts
  Resolver Based Options
  Resolver Based Ordering Procedure
Pressroom eNewsletter
Subscribe to our mailing list and you will receive information on new products, Trade Show appearances and answers to your questions.

Need a Quote? Contact our Sales Department >> 

Need Tech Support? Contact our Engineering Department >>

Pressroom Electronics